##// END OF EJS Templates
upstream » mercurial-mirror
RSS

Clone from https://www.mercurial-scm.org/repo/hg-all

lfs: bypass wrapped functions when reposetup() hasn't been called (issue5902)...
lfs: bypass wrapped functions when reposetup() hasn't been called (issue5902) There are only a handful of methods that access repo attributes that are applied in reposetup(). The `diff` test covers all of the commands that call scmutil.prefetchfiles(). Along the way, I saw that adding files and upgrading the repo format were also problems (also tested here). I don't think running `hg serve` through the commandserver is sane, but I conditionalized both the capabilities and the wsgirequest handler because it's trivially correct. It doesn't look like there has ever been a caller of candownload(), so there's no test for that path. The upload case isn't testable, because uploadblobs() bails if there are no pointers. The requirement should be added any time pointers are introduced, and that would force the extension to be loaded specifically for the repo. This covers `debuglfsupload`, the pre-push hook (which isn't set until the repo is promoted to LFS), and uploadblobsfromrevs(), which can be called by other extensions. I think readfromstore() and writetostore() are only reachable as a flag processor for revlog.REVIDX_EXTSTORED, and a requirement is added as soon as that is seen, so I don't think those are a problem.
Gregory Szorc - - Load All Authors

File last commit:

r36469:1fa35ca3 default
r38199:3790efb3 stable
Show More
bundles.txt
93 lines | 3.2 KiB | text/plain | TextLexer
/ mercurial / help / internals / bundles.txt
History | Annotation | Raw |Copy content |Copy permalink
A bundle is a container for repository data.
Bundles are used as standalone files as well as the interchange format
over the wire protocol used when two Mercurial peers communicate with
each other.
Headers
=======
Bundles produced since Mercurial 0.7 (September 2005) have a 4 byte
header identifying the major bundle type. The header always begins with
``HG`` and the follow 2 bytes indicate the bundle type/version. Some
bundle types have additional data after this 4 byte header.
The following sections describe each bundle header/type.
HG10
----
``HG10`` headers indicate a *changegroup bundle*. This is the original
bundle format, so it is sometimes referred to as *bundle1*. It has been
present since version 0.7 (released September 2005).
This header is followed by 2 bytes indicating the compression algorithm
used for data that follows. All subsequent data following this
compression identifier is compressed according to the algorithm/method
specified.
Supported algorithms include the following.
``BZ``
*bzip2* compression.
Bzip2 compressors emit a leading ``BZ`` header. Mercurial uses this
leading ``BZ`` as part of the bundle header. Therefore consumers
of bzip2 bundles need to *seed* the bzip2 decompressor with ``BZ`` or
seek the input stream back to the beginning of the algorithm component
of the bundle header so that decompressor input is valid. This behavior
is unique among supported compression algorithms.
Supported since version 0.7 (released December 2006).
``GZ``
*zlib* compression.
Supported since version 0.9.2 (released December 2006).
``UN``
*Uncompressed* or no compression. Unmodified changegroup data follows.
Supported since version 0.9.2 (released December 2006).
3rd party extensions may implement their own compression. However, no
authority reserves values for their compression algorithm identifiers.
HG2X
----
``HG2X`` headers (where ``X`` is any value) denote a *bundle2* bundle.
Bundle2 bundles are a container format for various kinds of repository
data and capabilities, beyond changegroup data (which was the only data
supported by ``HG10`` bundles.
``HG20`` is currently the only defined bundle2 version.
The ``HG20`` format is documented at :hg:`help internals.bundle2`.
Initial ``HG20`` support was added in Mercurial 3.0 (released May
2014). However, bundle2 bundles were hidden behind an experimental flag
until version 3.5 (released August 2015), when they were enabled in the
wire protocol. Various commands (including ``hg bundle``) did not
support generating bundle2 files until Mercurial 3.6 (released November
2015).
HGS1
----
*Experimental*
A ``HGS1`` header indicates a *streaming clone bundle*. This is a bundle
that contains raw revlog data from a repository store. (Typically revlog
data is exchanged in the form of changegroups.)
The purpose of *streaming clone bundles* are to *clone* repository data
very efficiently.
The ``HGS1`` header is always followed by 2 bytes indicating a
compression algorithm of the data that follows. Only ``UN``
(uncompressed data) is currently allowed.
``HGS1UN`` support was added as an experimental feature in version 3.6
(released November 2015) as part of the initial offering of the *clone
bundles* feature.