##// END OF EJS Templates
upstream » mercurial-mirror
RSS

Clone from https://www.mercurial-scm.org/repo/hg-all

exchange: improve computation of relevant markers for large repos...
exchange: improve computation of relevant markers for large repos Compute the candidate nodes with relevant markers directly from keys of the predecessors/successors/children dictionaries of obsstore. This is faster than iterating over all nodes directly. This test could be further improved for repositories with relative few markers compared to the repository size, but this is no longer hot already. With the current loop structure, the obshashrange use works as well as before as it passes lists with a single node. Adjust the interface by allowing revision lists as well as node lists. This helps cases that computes ancestors as it reduces the materialisation cost. Use this in _pushdiscoveryobsmarker and _getbundleobsmarkerpart. Improve the latter further by directly using ancestors(). Performance benchmarks show notable and welcome improvement to no-op push and pull (that would also apply to other push/pull). This apply to push and pull done without evolve. ### push/pull Benchmark parameter # bin-env-vars.hg.flavor = default # benchmark.variants.explicit-rev = none # benchmark.variants.protocol = ssh # benchmark.variants.revs = none ## benchmark.name = hg.command.pull # data-env-vars.name = mercurial-devel-2024-03-22-zstd-sparse-revlog before: 5.968537 seconds after: 5.668507 seconds (-5.03%, -0.30) # data-env-vars.name = tryton-devel-2024-03-22-zstd-sparse-revlog before: 1.446232 seconds after: 0.835553 seconds (-42.23%, -0.61) # data-env-vars.name = netbsd-src-draft-2024-09-19-zstd-sparse-revlog before: 5.777412 seconds after: 2.523454 seconds (-56.32%, -3.25) ## benchmark.name = hg.command.push # data-env-vars.name = mercurial-devel-2024-03-22-zstd-sparse-revlog before: 6.155501 seconds after: 5.885072 seconds (-4.39%, -0.27) # data-env-vars.name = tryton-devel-2024-03-22-zstd-sparse-revlog before: 1.491054 seconds after: 0.934882 seconds (-37.30%, -0.56) # data-env-vars.name = netbsd-src-draft-2024-09-19-zstd-sparse-revlog before: 5.902494 seconds after: 2.957644 seconds (-49.89%, -2.94) There is not notable different in these result using the "rust" flavor instead of the "default". The performance impact on the same operation when using evolve were also tested and no impact was noted.
Matt Harbison - - Load All Authors

File last commit:

r44031:2e017696 default
r52789:8583d138 default
Show More
diffs.txt
29 lines | 1.3 KiB | text/plain | TextLexer
/ mercurial / helptext / diffs.txt
History | Annotation | Raw |Copy content |Copy permalink
Mercurial's default format for showing changes between two versions of
a file is compatible with the unified format of GNU diff, which can be
used by GNU patch and many other standard tools.
While this standard format is often enough, it does not encode the
following information:
- executable status and other permission bits
- copy or rename information
- changes in binary files
- creation or deletion of empty files
Mercurial also supports the extended diff format from the git VCS
which addresses these limitations. The git diff format is not produced
by default because a few widespread tools still do not understand this
format.
This means that when generating diffs from a Mercurial repository
(e.g. with :hg:`export`), you should be careful about things like file
copies and renames or other things mentioned above, because when
applying a standard diff to a different repository, this extra
information is lost. Mercurial's internal operations (like push and
pull) are not affected by this, because they use an internal binary
format for communicating changes.
To make Mercurial produce the git extended diff format, use the --git
option available for many commands, or set 'git = True' in the [diff]
section of your configuration file. You do not need to set this option
when importing diffs in this format or using them in the mq extension.