##// END OF EJS Templates
exchange: improve computation of relevant markers for large repos...
exchange: improve computation of relevant markers for large repos Compute the candidate nodes with relevant markers directly from keys of the predecessors/successors/children dictionaries of obsstore. This is faster than iterating over all nodes directly. This test could be further improved for repositories with relative few markers compared to the repository size, but this is no longer hot already. With the current loop structure, the obshashrange use works as well as before as it passes lists with a single node. Adjust the interface by allowing revision lists as well as node lists. This helps cases that computes ancestors as it reduces the materialisation cost. Use this in _pushdiscoveryobsmarker and _getbundleobsmarkerpart. Improve the latter further by directly using ancestors(). Performance benchmarks show notable and welcome improvement to no-op push and pull (that would also apply to other push/pull). This apply to push and pull done without evolve. ### push/pull Benchmark parameter # bin-env-vars.hg.flavor = default # benchmark.variants.explicit-rev = none # benchmark.variants.protocol = ssh # benchmark.variants.revs = none ## benchmark.name = hg.command.pull # data-env-vars.name = mercurial-devel-2024-03-22-zstd-sparse-revlog before: 5.968537 seconds after: 5.668507 seconds (-5.03%, -0.30) # data-env-vars.name = tryton-devel-2024-03-22-zstd-sparse-revlog before: 1.446232 seconds after: 0.835553 seconds (-42.23%, -0.61) # data-env-vars.name = netbsd-src-draft-2024-09-19-zstd-sparse-revlog before: 5.777412 seconds after: 2.523454 seconds (-56.32%, -3.25) ## benchmark.name = hg.command.push # data-env-vars.name = mercurial-devel-2024-03-22-zstd-sparse-revlog before: 6.155501 seconds after: 5.885072 seconds (-4.39%, -0.27) # data-env-vars.name = tryton-devel-2024-03-22-zstd-sparse-revlog before: 1.491054 seconds after: 0.934882 seconds (-37.30%, -0.56) # data-env-vars.name = netbsd-src-draft-2024-09-19-zstd-sparse-revlog before: 5.902494 seconds after: 2.957644 seconds (-49.89%, -2.94) There is not notable different in these result using the "rust" flavor instead of the "default". The performance impact on the same operation when using evolve were also tested and no impact was noted.

File last commit:

r44031:2e017696 default
r52789:8583d138 default
Show More
cbor.txt
130 lines | 3.8 KiB | text/plain | TextLexer
Mercurial uses Concise Binary Object Representation (CBOR)
(RFC 7049) for various data formats.
This document describes the subset of CBOR that Mercurial uses and
gives recommendations for appropriate use of CBOR within Mercurial.
Type Limitations
================
Major types 0 and 1 (unsigned integers and negative integers) MUST be
fully supported.
Major type 2 (byte strings) MUST be fully supported. However, there
are limitations around the use of indefinite-length byte strings.
(See below.)
Major type 3 (text strings) are NOT supported.
Major type 4 (arrays) MUST be supported. However, values are limited
to the set of types described in the "Container Types" section below.
And indefinite-length arrays are NOT supported.
Major type 5 (maps) MUST be supported. However, key values are limited
to the set of types described in the "Container Types" section below.
And indefinite-length maps are NOT supported.
Major type 6 (semantic tagging of major types) can be used with the
following semantic tag values:
258
Mathematical finite set. Suitable for representing Python's
``set`` type.
All other semantic tag values are not allowed.
Major type 7 (simple data types) can be used with the following
type values:
20
False
21
True
22
Null
31
Break stop code (for indefinite-length items).
All other simple data type values (including every value requiring the
1 byte extension) are disallowed.
Indefinite-Length Byte Strings
==============================
Indefinite-length byte strings (major type 2) are allowed. However,
they MUST NOT occur inside a container type (such as an array or map).
i.e. they can only occur as the "top-most" element in a stream of
values.
Encoders and decoders SHOULD *stream* indefinite-length byte strings.
i.e. an encoder or decoder SHOULD NOT buffer the entirety of a long
byte string value when indefinite-length byte strings are being used
if it can be avoided. Mercurial MAY use extremely long indefinite-length
byte strings and buffering the source or destination value COULD lead to
memory exhaustion.
Chunks in an indefinite-length byte string SHOULD NOT exceed 2^20
bytes.
Container Types
===============
Mercurial may use the array (major type 4), map (major type 5), and
set (semantic tag 258 plus major type 4 array) container types.
An array may contain any supported type as values.
A map MUST only use the following types as keys:
* unsigned integers (major type 0)
* negative integers (major type 1)
* byte strings (major type 2) (but not indefinite-length byte strings)
* false (simple type 20)
* true (simple type 21)
* null (simple type 22)
A map MUST only use the following types as values:
* all types supported as map keys
* arrays
* maps
* sets
A set may only use the following types as values:
* all types supported as map keys
It is recommended that keys in maps and values in sets and arrays all
be of a uniform type.
Avoiding Large Byte Strings
===========================
The use of large byte strings is discouraged, especially in scenarios where
the total size of the byte string may by unbound for some inputs (e.g. when
representing the content of a tracked file). It is highly recommended to use
indefinite-length byte strings for these purposes.
Since indefinite-length byte strings cannot be nested within an outer
container (such as an array or map), to associate a large byte string
with another data structure, it is recommended to use an array or
map followed immediately by an indefinite-length byte string. For example,
instead of the following map::
{
"key1": "value1",
"key2": "value2",
"long_value": "some very large value...",
}
Use a map followed by a byte string:
{
"key1": "value1",
"key2": "value2",
"value_follows": True,
}
<BEGIN INDEFINITE-LENGTH BYTE STRING>
"some very large value"
"..."
<END INDEFINITE-LENGTH BYTE STRING>